Disassembling the Slide
To disassemble the slide, comply with these steps:
1. Maintain the slide grip along with your non-dominant hand and pull the slide to the rear till it locks open.
2. Rotate the barrel bushing clockwise till it’s totally unscrewed.
3. Fastidiously pull the barrel ahead and out of the slide.
4. Rotate the recoil spring plug clockwise till it’s totally unscrewed.
5. Take away the recoil spring plug, recoil spring, and information rod from the slide.
Eradicating the Firing Pin Meeting
To take away the firing pin meeting, comply with these steps:
- Depress the firing pin security situated on the left aspect of the slide.
- Fastidiously carry the firing pin meeting out of the slide.
Word: Be cautious when eradicating the firing pin meeting as it’s underneath spring pressure.
Eradicating the Extractor
To take away the extractor, comply with these steps:
- Depress the extractor pin situated on the left aspect of the slide.
- Extract the extractor from the slide.
Word: The extractor spring might fly out when the extractor is eliminated. Remember to retrieve it.
Disassembling the Body
To disassemble the body, comply with these steps:
1. Take away the slide.
Retract the slide totally to the rear and carry it up barely. Tilt the slide ahead and pull it off the body.
2. Take away the recoil spring and information rod.
Grasp the recoil spring meeting by the knurled finish and pull it straight out of the body.
3. Take away the barrel.
Tilt the barrel up and pull it ahead to take away it from the body.
4. Take away the set off group.
Insert a small punch into the opening situated behind the set off and push ahead to launch the set off group. Pull the set off group straight right down to take away it from the body.
**Tip:** Earlier than eradicating the set off group, it’s endorsed to first take away the journal launch and slide cease.
5. Take away the grip panels.
Insert a small flat-head screwdriver into the slot situated on the backside of the grip panel. Pry the grip panel up and off the body. Repeat for the opposite grip panel.
6. Take away the body pin.
Use a punch to drive out the body pin situated on the high of the grip body. This may separate the body into two items.
Disassembling the Set off
The subsequent step is to take away the set off. The set off is held in place by a spring-loaded pin. To take away the set off, use a small screwdriver or punch to depress the spring-loaded pin. As soon as the pin is depressed, the set off may be eliminated.
The set off meeting consists of a number of elements, together with the set off, set off spring, and set off housing. To take away the set off meeting, it’s essential to disassemble these elements.
To take away the set off spring, depress the spring with a small screwdriver or punch. As soon as the spring is depressed, the set off may be faraway from the set off housing.
To take away the set off housing, use a small screwdriver or punch to take away the screw that secures the set off housing to the body. As soon as the screw is eliminated, the set off housing may be lifted off the body.
The set off meeting can now be disassembled. To take away the set off, use a small screwdriver or punch to depress the spring-loaded pin. As soon as the pin is depressed, the set off may be faraway from the set off meeting.
To take away the set off spring, depress the spring with a small screwdriver or punch. As soon as the spring is depressed, the set off may be faraway from the set off meeting.
To take away the set off housing, use a small screwdriver or punch to take away the screw that secures the set off housing to the body. As soon as the screw is eliminated, the set off housing may be lifted off the body.
| Part | Elimination Process |
|---|---|
| Set off | Depress spring-loaded pin and take away set off |
| Set off spring | Depress spring and take away set off |
| Set off housing | Take away screw and carry off body |
Eradicating the Hammer
To take away the hammer, start by eradicating the grip panels by unscrewing the screws on the again of the grip. Subsequent, drift out the roll pin that holds the hammer in place utilizing a punch. As soon as the roll pin is eliminated, fastidiously take away the hammer by pulling it straight up. Watch out to not lose the hammer spring, which will likely be underneath pressure.
With the hammer eliminated, now you can entry the sear and set off meeting. To take away the sear, drift out the roll pin that holds it in place. The set off may be eliminated by pushing out the set off pin from the left aspect of the body.
To reassemble the hammer, merely reverse the disassembly process. Insert the hammer into the body and align it with the hammer spring. Slide the roll pin again into place to safe the hammer. Subsequent, insert the sear and set off into the body and safe them with their respective roll pins. Lastly, reattach the grip panels to finish the meeting.
| Step | Description |
|---|---|
| 1 | Take away the grip panels. |
| 2 | Drift out the roll pin that holds the hammer in place. |
| 3 | Take away the hammer by pulling it straight up. |
| 4 | Drift out the roll pin that holds the sear in place. |
| 5 | Take away the sear. |
| 6 | Push out the set off pin from the left aspect of the body. |
| 7 | Take away the set off. |
Reassembling the Mp Bodyguard 380
To reassemble the MP Bodyguard 380, comply with these steps:
1. Insert the journal into the journal properly.
2. Insert the slide onto the body.
3. Pull the slide again and launch it to chamber a spherical.
4. Insert the slide cease pin into the body.
5. Insert the recoil spring into the body.
6. Insert the information rod into the recoil spring.
7. Insert the barrel into the slide.
8. Insert the slide cowl plate onto the slide.
| Half | Description |
|---|---|
| Slide | The slide is the shifting a part of the pistol that chambers the spherical and fires the cartridge. |
| Body | The body is the stationary a part of the pistol that holds the slide, barrel, journal, set off, and different inside elements. |
| Barrel | The barrel is the metallic tube by means of which the bullet travels when fired. |
| Recoil spring | The recoil spring is a coil spring that absorbs the recoil generated when the pistol is fired. |
| Journal | The journal is the removable unit that holds the rounds of ammunition. |
| Set off | The set off is the a part of the pistol that’s pulled to fireplace the gun. |
9. Insert the security selector change into the body.
10. Insert the mainspring housing into the body.
11. Insert the grip panels onto the body.
12. Examine the pistol to make sure that it’s correctly assembled and functioning.
Troubleshooting and Security Ideas
All the time comply with these security guidelines when disassembling any firearm:
- Preserve the gun pointed in a protected path always.
- Make sure the gun is unloaded.
- By no means work on a gun that’s loaded or cocked.
- All the time put on security glasses when engaged on a gun.
In the event you encounter any issues whereas disassembling your MP Bodyguard 380, confer with the troubleshooting ideas beneath:
| Downside | Answer |
|---|---|
| The slide will not come off the body. | Make certain the slide lock is totally disengaged. |
| The barrel will not come out of the slide. | Examine for any obstructions within the barrel, comparable to carbon buildup or particles. |
| The information rod will not come out of the slide. | Examine for any burrs or obstructions on the information rod or within the slide. |
| The set off will not reset. | Examine for any obstructions within the set off mechanism, comparable to dust or particles. |
| The security will not interact. | Examine for any obstructions within the security mechanism, comparable to dust or particles. |
| The journal will not drop free. | Examine for any obstructions within the journal catch or properly, comparable to dust or particles. |
| The recoil spring is just too robust. | Exchange the recoil spring with a weaker one. |
| The recoil spring is just too weak. | Exchange the recoil spring with a stronger one. |
| The firing pin is caught. | Examine for any obstructions within the firing pin channel, comparable to dust or particles. |
| The extractor is caught. | Examine for any obstructions within the extractor channel, comparable to dust or particles. |
In case you are unable to resolve the issue your self, please seek the advice of a certified gunsmith.
