Changing a belt on a Maytag washer W10873035 is a comparatively simple process that may be accomplished in about an hour. Crucial factor is to just remember to have the best belt to your mannequin of washer. You could find the proper belt by wanting up the mannequin variety of your washer within the Maytag elements catalog. Upon getting the proper belt, you’ll be able to comply with the steps beneath to put in it.
First, you will have to unplug the washer from the facility outlet and switch off the water provide. Subsequent, you will have to take away the again panel of the washer. To do that, find the screws which are holding the again panel in place and take away them. As soon as the screws are eliminated, it’s best to be capable of pull the again panel off of the washer. Now, you will have to find the belt. The belt is a protracted, black rubber band that’s wrapped across the motor pulley and the transmission pulley. To take away the belt, merely slip it off of the pulleys. Lastly, you will have to put in the brand new belt. To do that, merely slip the brand new belt over the motor pulley and the transmission pulley. As soon as the brand new belt is in place, you’ll be able to reattach the again panel of the washer. Guarantee that the belt is tight earlier than you reattach the again panel. To do that, merely flip the motor pulley by hand. The belt must be tight sufficient in order that it doesn’t slip off of the pulleys, however not so tight that it’s tough to show the motor pulley.
As soon as the again panel is reattached, you’ll be able to plug the washer again into the facility outlet and activate the water provide. Your washer ought to now be working correctly.
Eradicating the Washer’s Entrance Panel
To provoke the dismantling course of, meticulously unplug the washer’s energy wire from {the electrical} outlet. This significant security measure prevents any potential electrical hazards. Find the 2 screws securing the management panel to the highest of the washer’s entrance panel. Utilizing a Phillips head screwdriver, fastidiously take away these screws, being conscious to not injury the panel or surrounding parts.
Proceed to the underside of the entrance panel, the place you’ll encounter two further screws hidden behind the kickplate. These screws require a 1/4-inch hex head driver to extract. As soon as eliminated, gently pull the kickplate straight in the direction of you to detach it from the washer.
With the kickplate out of the best way, now you can give attention to eradicating the entrance panel. Firmly grasp the panel on either side and pull it in the direction of you with regular pressure. The panel will probably be held in place by a collection of plastic clips, which is able to launch with a mild tug. As soon as the clips are indifferent, slowly elevate the panel upwards and out of the washer.
Warning: Deal with the entrance panel with utmost care because it accommodates delicate electrical parts. Keep away from bending or twisting the panel to forestall injury.
| Instruments Required |
|---|
| Phillips Head Screwdriver |
| 1/4-Inch Hex Head Driver |
Detaching the Drive Belt
The drive belt is an important part that powers the washer’s drum motion. To entry and detach it, comply with these steps:
Eradicating the Washer Prime
1. Unplug the washer and disconnect the water hoses.
2. Find the 2 screws in the back of the washer, close to the highest. Take away them utilizing a screwdriver.
3. Rigorously elevate and take away the washer prime, setting it apart.
Accessing the Drive Belt
4. Find the drive belt pulley, which is normally hooked up to the motor on the backside of the washer.
5. Utilizing a pair of pliers or a spanner, gently pry the belt off the pulley.
6. As soon as the belt is indifferent, take away it from the washer.
Ideas for Detaching the Belt
- Be cautious when prying the belt off the pulley, as it could be underneath stress.
- If the belt is caught, use a small quantity of penetrating oil to loosen it.
- Word the belt’s orientation for correct reinstallation.
| Part | Removing Course of |
|---|---|
| Washer Prime | Unplug, take away water hoses, unscrew and elevate off |
| Drive Belt | Pry off pulley utilizing pliers or spanner |
| Belt Stress | Use penetrating oil if caught |
| Belt Orientation | Word place for reinstallation |
Putting in the New Drive Belt
4. Putting in the New Drive Belt
a) Place the brand new drive belt across the motor pulley, guaranteeing that it’s seated appropriately within the groove.
b) Route the belt across the loafer pulley and tensioner pulley, following the proper routing diagram as per your washer mannequin.
c) Place the belt across the transmission pulley, ensuring to align it with the groove and information pins.
d) Manually rotate the transmission pulley clockwise till the belt is tight. Verify the strain by making use of mild stress to the belt; it ought to deflect about 1/2 to 1 inch when pressed.
e) Tighten the tensioner pulley bolt or nut to safe the belt in place. Don’t overtighten, as this could injury the belt or pulley.
f) Reconnect {the electrical} connectors to the transmission and motor.
g) Change the again panel of the washer and safe it with screws.
Reattaching the Washer’s Entrance Panel
As soon as the brand new belt has been put in, it is time to reattach the washer’s entrance panel. This is how:
1. Align the Panel
Rigorously align the entrance panel with the washer’s body, guaranteeing that the perimeters are flush and the panel is degree.
2. Insert Prime Tabs
Find the 2 tabs on the prime of the entrance panel and thoroughly insert them into the slots on the washer’s body.
3. Push Down
Gently push down on the highest of the entrance panel till you hear a click on, indicating that the tabs have snapped into place.
4. Insert Backside Clips
Find the 2 clips on the backside of the entrance panel and slide them into the slots on the washer’s body.
5. Safe Screws
Use a screwdriver to tighten the screws that safe the entrance panel to the body, guaranteeing that they’re comfortable however not overtightened.
6. Set up Kick Plate
The kick plate is an ornamental panel that covers the underside of the washer. To put in it, comply with these steps:
| Step | Directions |
|---|---|
| a) | Place the kick plate on the backside of the entrance panel. |
| b) | Insert the tabs on the kick plate into the slots on the entrance panel. |
| c) | Push down on the kick plate till it snaps into place. |
| d) | Use a screwdriver to tighten the screws that safe the kick plate to the entrance panel. |
Verifying Correct Belt Set up
After changing the belt, it is essential to confirm its correct set up. Comply with these steps:
- Right Belt Path: Make sure the belt follows the proper path across the motor pulley, loafer pulley (if current), and transmission pulley.
- No Slack: The belt must be taut with no slack between the pulleys. A unfastened belt can slip and compromise efficiency.
- No Interference: Confirm that the belt doesn’t intervene or rub towards every other parts, akin to wires, hoses, or the washer cupboard.
- Balanced Stress: The belt ought to have equal stress on either side. Use a belt stress gauge or your fingers to verify for any imbalances.
- Clean Rotation: With the facility off, manually rotate the motor pulley to verify for any binding or extreme resistance. The pulleys ought to spin easily with a mild push.
- Listening for Noises: Run a take a look at cycle to pay attention for any irregular noises coming from the belt space. A squealing or grinding sound might point out misalignment or a broken belt.
- Efficiency Verify: If the belt seems to be put in appropriately, run a full wash cycle to verify for correct performance. The washer ought to agitate, spin, and drain usually with none belt-related points.
Supplies You may Want
Earlier than beginning, collect the next supplies:
– New drive belt (half quantity W10873035)
– Socket wrench or pliers
– Screwdriver
– Flashlight (elective)
Security Precautions
Unplug the washer from the facility outlet earlier than starting any repairs.
Put on gloves and security glasses to guard your self from sharp edges and particles.
Step-by-Step Directions
1.
Take away the Prime Panel
Find the 2 screws holding the highest panel in place. Take away the screws and elevate the highest panel off the washer.
2.
Find the Drive Belt
The drive belt is situated across the motor pulley and the transmission pulley on the backside of the washer.
3.
Take away the Outdated Belt
Use a socket wrench or pliers to loosen the strain on the belt. Slip the belt off the pulleys and take away it from the washer.
4.
Set up the New Belt
Place the brand new belt across the motor pulley first. Then, stretch the belt over the transmission pulley and alter the strain utilizing the socket wrench or pliers.
5.
Change the Prime Panel
Align the highest panel with the washer and press it down till it clicks into place.
6.
Reconnect the Energy
Plug the washer again into the facility outlet.
7.
Check the Washer
Run the washer by a brief cycle to make sure that the brand new belt is working correctly.
Frequent Troubleshooting Ideas
The belt retains coming off
1. Verify the strain on the belt. It must be tight sufficient to remain on the pulleys, however not so tight that it places pressure on the motor.
2. Make sure the belt is routed appropriately across the pulleys.
3. Examine the pulleys for injury. If they’re worn or broken, they might should be changed.
4. Verify for different objects that could be caught within the belt, akin to unfastened clothes or particles.
5. Change the belt with a brand new one whether it is broken or stretched.
6. Verify the motor bearings. If they’re worn or broken, they might trigger the motor pulley to wobble, which may trigger the belt to come back off.
7. Examine the transmission. Whether it is broken or worn, it could not be capable of flip the bathtub correctly, which may trigger the belt to come back off.
8. Verify the motor capacitor. If it’s not working correctly, it may possibly trigger the motor to run erratically, which may result in the belt coming off. The motor capacitor is a cylindrical part that’s related to the motor. It’s normally black or brown in coloration. To check the capacitor, you will have a multimeter. Disconnect the facility to the washer earlier than testing the capacitor. Set the multimeter to the capacitance setting and contact the probes to the terminals on the capacitor.
Security Precautions for Washer Belt Set up
1. Unplug the washer or disconnect it from the facility provide earlier than beginning any work.
2. Put on protecting gloves and security glasses to keep away from accidents from sharp edges or chemical compounds.
3. Make sure the washer is secure and degree earlier than making an attempt to put in the belt.
4. Clear the realm across the washer of any obstacles or particles.
5. Have a helper help you with lifting the equipment if needed.
6. Ensure that the washer is in its off cycle and the lid is open.
7. Take away the again or entrance panel of the washer, relying on the mannequin.
8. Find the previous belt and thoroughly detach it from the pulleys.
9. Examine the Belt for Injury
Examine the previous belt for any indicators of harm, together with cracks, cuts, fraying, or extreme put on. If any injury is discovered, substitute the previous belt with a brand new one to make sure optimum efficiency.
To completely examine the belt, use a magnifying glass to look at its floor for effective cracks or tears. Pay specific consideration to the areas the place the belt bends and makes contact with the pulleys.
Really feel the belt’s texture to detect any tough spots, thinning, or areas the place the rubber has hardened or turn into brittle. These indications may sign potential breakage or slippage throughout operation.
Further Ideas and Issues
Unplug the washer earlier than beginning.
It is a essential security precaution to forestall any electrical shocks whereas engaged on the washer.
Collect the required instruments.
You will want a screwdriver, a wrench, and a brand new belt.
Find the belt.
The belt is normally situated across the motor pulley and the transmission pulley.
Take away the previous belt.
Use the wrench to loosen the strain on the belt after which slip it off the pulleys.
Set up the brand new belt.
Slip the brand new belt onto the motor pulley first after which onto the transmission pulley. Ensure that the belt is correctly aligned and seated within the grooves.
Tighten the belt.
Use the wrench to tighten the strain on the belt. The belt must be tight sufficient to forestall slipping however not so tight that it places pointless pressure on the motor or the transmission.
Reassemble the washer.
Put the entrance panel again on and fasten the screws.
Check the washer.
Plug the washer again in and run it by a brief cycle to verify it’s working correctly.
10. Belt Stress Adjustment
Correct belt stress is essential for optimum washer efficiency. If the belt is simply too unfastened, it could slip and trigger the washer to vibrate or make noise. If the belt is simply too tight, it could put pointless pressure on the motor and the transmission, resulting in untimely failure.
To regulate the belt stress, comply with these steps:
| Step | Description |
|---|---|
| 1 | Loosen the 2 bolts that maintain the motor mount in place. |
| 2 | Transfer the motor ahead or backward to regulate the belt stress. |
| 3 | Tighten the bolts to safe the motor mount in place. |
| 4 | Run the washer by a brief cycle to verify the belt stress. |
Repeat these steps till the belt stress is right.
How To Set up Belt On Maytag Washer W10873035
Changing the belt on a Maytag washer mannequin W10873035 is a comparatively easy restore that may be accomplished in about an hour. Crucial factor is to just remember to have the proper belt to your mannequin and that you simply comply with the directions fastidiously.
Supplies:
- New belt
- Screwdriver
- Bucket
Directions:
- Unplug the washer from the facility outlet.
- Flip off the water provide to the washer.
- Disconnect the drain hose from the standpipe.
- Tilt the washer again barely and place a bucket underneath the underside entrance of the washer to catch any water which will leak out.
- Take away the 2 screws that maintain the entrance panel in place.
- Pull the entrance panel ahead and off the washer.
- Find the belt across the motor pulley and the transmission pulley.
- Loosen the loafer pulley with a screwdriver.
- Take away the previous belt from the pulleys.
- Place the brand new belt across the motor pulley and the transmission pulley.
- Tighten the loafer pulley.
- Change the entrance panel.
- Reconnect the drain hose to the standpipe.
- Activate the water provide to the washer.
- Plug the washer into the facility outlet.
- Run the washer by a take a look at cycle.
Individuals Additionally Ask About How To Set up Belt On Maytag Washer W10873035
Can I substitute the belt on my Maytag washer myself?
Sure, changing the belt on a Maytag washer is a comparatively easy restore that may be accomplished in about an hour. Nevertheless, it is very important just remember to have the proper belt to your mannequin and that you simply comply with the directions fastidiously.
How do I do know if the belt on my Maytag washer is damaged?
There are a number of indicators which will point out that the belt in your Maytag washer is damaged. These embody:
- The washer won’t agitate or spin.
- The washer makes a squealing or thumping noise.
- The washer leaks water.
How a lot does it price to exchange the belt on a Maytag washer?
The fee to exchange the belt on a Maytag washer will range relying on the mannequin of the washer and the price of the belt. Nevertheless, you’ll be able to count on to pay between $50 and $100 for the restore.
