Putting in jigsaw blades on DeWalt 20-volt jigsaws is usually a breeze! Here is a step-by-step information that will help you get it achieved shortly and effectively. Start by making certain that your jigsaw is off and the battery is disconnected. It is essential to work on a cooled-down jigsaw to stop any burns.
Find the blade ejection lever on the entrance of the noticed. It’s usually a small, spring-loaded lever. Push the lever away from you and concurrently pull down the blade clamp. This may can help you clear the trail for the brand new blade. Subsequent, align the brand new blade’s tooth going through downwards and insert it into the blade clamp. Fastidiously push the blade up till it’s securely held in place. Launch the blade clamp by pushing it in direction of you and lock the blade in place by participating the blade ejection lever again into its unique place. Make sure the blade is firmly seated by gently pulling on it.
Lastly, reconnect the battery and activate the jigsaw. Check the blade by making just a few cuts on a scrap piece of wooden. If the blade cuts easily with none wobbling or vibration, you could have efficiently put in the blade. Bear in mind, it is indispensable to put on gloves and security glasses all through the method on your safety.
Disassembling the Jigsaw
Earlier than you possibly can insert a brand new blade into your DeWalt 20V jigsaw, you have to first disassemble the device. Comply with these steps to take action safely and effectively:
1. Unplug the Jigsaw
At first, it’s essential to unplug the jigsaw from the facility supply. This security precaution prevents unintentional activation whereas disassembling the device. Find the facility wire and disconnect it on the plug.
As soon as the jigsaw is unplugged, you possibly can proceed to the following steps.
2. Take away the Shoe Insert
The shoe insert is a small, detachable piece situated on the bottom of the jigsaw. To take away it, merely grasp the insert along with your fingers or a pair of pliers and pull it straight out. This may expose the blade clamp mechanism beneath.
3. Open the Blade Clamp
With the shoe insert eliminated, you will notice a steel blade clamp. To open the clamp, find the lever or knob on the facet of the jigsaw and rotate it counterclockwise. This may loosen the clamp and can help you insert or take away the jigsaw blade safely.
4. Take away the Previous Blade
As soon as the blade clamp is open, you possibly can take away the previous blade. Grip the blade firmly with one hand and gently pull it straight up out of the clamp. If the blade is caught, you could want to make use of a pair of pliers or a screwdriver to assist pry it free.
Inserting the New Blade
As soon as you’ve got chosen the suitable blade on your challenge, it is time to insert it into the jigsaw. Here is an in depth step-by-step information:
Step 1: Take away the Base Plate
Loosen the screws holding the bottom plate in place utilizing an Allen key or wrench. Fastidiously raise off the bottom plate to show the blade clamp.
Step 2: Open the Blade Clamp
Find the lever or dial that releases the blade clamp. Press or flip the discharge mechanism to open the clamp and permit the insertion of the brand new blade.
Step 3: Insert the Blade
Align the tooth of the brand new blade with the information slots on the blade clamp. Insert the blade into the clamp making certain that the tooth are going through within the appropriate course. The blade must be inserted with the tooth pointing downward for slicing on the upstroke and upward for slicing on the downstroke.
| Slicing Course | Enamel Orientation |
|---|---|
| Upstroke (Slicing on the best way up) | Enamel going through downward |
| Downstroke (Slicing on the best way down) | Enamel going through upward |
Tip: When you’re uncertain of the proper tooth orientation, seek the advice of your jigsaw’s handbook or test the producer’s web site for particular steering.
Step 4: Shut the Blade Clamp
As soon as the blade is inserted, press or flip the discharge mechanism once more to shut the blade clamp. Be certain that the blade is securely held in place with none wobble.
Step 5: Reattach the Base Plate
Place the bottom plate again onto the jigsaw and tighten the screws to safe it. Your new jigsaw blade is now put in and prepared to be used.
Securing the Blade
4. Tightening the Blade: A Complete Information
As soon as the blade is seated appropriately, it is essential to tighten it securely. Use the supplied wrench or key to carry the retaining bolt nonetheless when you flip the nut clockwise utilizing the opposite hand. Guarantee you could have a agency grip and apply sufficient drive to snugly fasten the blade, however keep away from overtightening as it might warp or harm the blade. To make sure correct tightness, use a torque wrench set to the producer’s beneficial torque specification. Nevertheless, should you’re working with out a torque wrench, intention for a comfortable match that enables the blade to maneuver freely with out extreme play.
| Tip | Clarification |
|---|---|
| Safe the blade firmly, however do not overtighten | Overtightening can warp or harm the blade |
| Use a torque wrench for exact tightening | Ensures correct tightness with out damaging the blade |
| Purpose for a comfortable match with out extreme play | Permits the blade to maneuver freely throughout slicing |
Adjusting Blade Pressure
As soon as you’ve got inserted the blade, you will want to regulate the blade pressure to make sure it is held securely. Most DeWalt jigsaws have a tool-less blade pressure lever or knob that means that you can simply regulate the stress with out the necessity for a hex key or different instruments. Here is tips on how to regulate the blade pressure:
- Establish the blade pressure adjustment lever or knob in your particular DeWalt jigsaw mannequin.
- Maintain the lever or knob and switch it counterclockwise to loosen the blade pressure.
- Insert the blade into the jigsaw and tighten the lever or knob clockwise till the blade is held firmly in place.
- Check the blade pressure by gently pulling on the blade. It ought to really feel cosy however not overly tight.
- If the blade strikes too simply or rattles, tighten the stress lever or knob additional. If the blade is simply too tight, it might bind or break throughout operation, so loosen the stress barely.
Suggestions for Adjusting Blade Pressure
- Totally different blades might require completely different pressure settings. Thinner blades usually require much less pressure than thicker blades.
- At all times test the blade pressure earlier than every use to make sure it is safe and correctly adjusted.
- Keep away from overtightening the blade pressure, as this will harm the blade or the jigsaw mechanism.
Security Precautions
1. Put on Security Gear: At all times put on eye safety, gloves, and a mud masks when working with energy instruments.
2. Unplug Energy Device: Earlier than performing any upkeep or changes, be sure that the jigsaw is unplugged from the facility supply.
3. Examine Blade: Examine the blade for any harm or put on earlier than set up. Don’t use a broken blade.
4. Maintain Away from Blade: Maintain your fingers and fingers away from the blade space whereas the jigsaw is operating.
5. Securely Clamp Workpiece: Safe the workpiece firmly earlier than beginning to minimize. This may stop the fabric from shifting throughout the slicing course of.
6. Keep away from Kickbacks: Preserve a agency grip on the jigsaw and use each fingers to regulate the device. Keep away from slicing into supplies which can be too thick or arduous, as this will trigger kickbacks.
7. Use Right Blade: Select the proper blade for the fabric you might be slicing. Incorrect blade choice can result in ineffective slicing and potential hazards.
8. Comply with Producers’ Directions: Seek advice from the producer’s directions for particular security tips and upkeep procedures.
9. Extra Precautions for 20 Volt DeWalt Jigsaws:
- Take away Battery Earlier than Altering Blade: At all times take away the battery from the jigsaw earlier than altering the blade.
- Find Blade Clamp Lever: Establish the blade clamp lever on the jigsaw, normally situated close to the blade housing.
- Pull Up Clamp Lever: Pull up the blade clamp lever to launch the blade.
- Take away Previous Blade: Grip the previous blade firmly with gloved fingers and pull it straight out of the blade holder.
- Insert New Blade: Align the brand new blade with the blade holder and insert it securely.
- Safe Blade: Push down on the blade clamp lever to safe the brand new blade in place.
- Examine Blade Set up: Be certain that the blade is correctly put in and securely mounted earlier than persevering with.
Putting in Dewalt Jigsaw Blades 20 Volt
Step 1: Collect Supplies
You will want a Dewalt jigsaw, a Dewalt 20V jigsaw blade, and a Phillips head screwdriver.
Step 2: Put together the Jigsaw
Take away the battery from the jigsaw and insert the jigsaw blade into the blade clamp.
Step 3: Tighten the Blade Clamp
Use the Phillips head screwdriver to tighten the blade clamp screw till the blade is securely held.
Step 4: Reattach the Battery
Reattach the battery to the jigsaw.
Step 5: Check the Blade
Activate the jigsaw and make just a few take a look at cuts to make sure the blade is put in appropriately and slicing easily.
Troubleshooting Suggestions
1. The blade isn’t slicing straight
Examine if the blade is put in appropriately and if the blade clamp is tight. If the issue persists, attempt a brand new blade.
2. The blade is vibrating excessively
Examine if the blade is bent or broken. Whether it is, substitute the blade. Additionally, test if the jigsaw is balanced correctly and if the blade clamp is tight.
3. The blade isn’t slicing by way of the fabric
Examine if the blade is sharp and if the jigsaw is about to the proper velocity for the fabric being minimize. If the issue persists, attempt a unique blade.
4. The jigsaw is overheating
Cease utilizing the jigsaw and let it calm down. Examine if the blade is caught or if the jigsaw is clogged with sawdust. Clear the jigsaw and take a look at utilizing a brand new blade.
5. The jigsaw is making unusual noises
Cease utilizing the jigsaw and test if there are any free elements or broken elements. When you discover any issues, contact a certified restore technician.
6. The jigsaw isn’t beginning
Examine if the battery is charged and if the jigsaw is correctly plugged into an outlet. If the issue persists, attempt a unique battery or contact a certified restore technician.
7. The jigsaw isn’t responding to the set off
Examine if the set off is caught or broken. Whether it is, contact a certified restore technician.
8. The jigsaw is smoking
Cease utilizing the jigsaw instantly and unplug it from the outlet. Contact a certified restore technician.
9. The jigsaw is leaking oil
Cease utilizing the jigsaw and phone a certified restore technician.
10. The jigsaw isn’t coated by the guarantee
If the jigsaw isn’t coated by the guarantee, you possibly can contact a certified restore technician. They’ll diagnose the issue and supply a price estimate for the repairs.
How To Set up Dewalt Jigsaw Blades 20 Volt
Putting in Dewalt jigsaw blades on a 20-volt jigsaw is an easy course of that may be accomplished in a couple of minutes. Listed here are the steps it’s essential to comply with:
- Flip off the jigsaw and unplug it from the facility supply. That is vital for security causes.
- Open the blade clamp. To do that, push the lever or button that’s situated on the facet of the jigsaw. The blade clamp will open, permitting you to take away the previous blade.
- Take away the previous blade. Grip the previous blade along with your fingers and pull it straight out of the blade clamp.
- Insert the brand new blade. Align the brand new blade with the blade clamp and insert it into the clamp. Make it possible for the tooth of the blade are going through within the appropriate course.
- Shut the blade clamp. Push the lever or button that you simply used to open the blade clamp. The blade clamp will shut, securing the brand new blade in place.
- Plug within the jigsaw and switch it on. Your jigsaw is now prepared to make use of.
Folks Additionally Ask About How To Set up Dewalt Jigsaw Blades 20 Volt
What’s one of the simplest ways to chop a straight line with a jigsaw?
To chop a straight line with a jigsaw, use a straight edge as a information. Place the straight edge alongside the road you need to minimize and maintain it firmly in place. Then, begin slicing alongside the road, holding the jigsaw towards the straight edge.
What’s one of the simplest ways to chop a curve with a jigsaw?
To chop a curve with a jigsaw, use a freehand approach. Begin by slicing alongside the surface fringe of the curve. Then, step by step transfer the jigsaw in direction of the within fringe of the curve, ensuring to maintain the blade perpendicular to the floor of the fabric.
What’s one of the simplest ways to chop a gap with a jigsaw?
To chop a gap with a jigsaw, first drill a pilot gap within the heart of the outlet. Then, insert the jigsaw blade into the pilot gap and begin slicing. Maintain the jigsaw perpendicular to the floor of the fabric and step by step transfer the jigsaw across the circumference of the outlet.
