Whenever you’re ending a quilt, one of many final steps is to affix the ends of the binding. This is usually a difficult activity, nevertheless it’s essential to do it accurately to make sure a professional-looking end. On this article, we’ll stroll you thru the steps on find out how to be a part of quilt binding ends completely. We’ll additionally present recommendations on find out how to keep away from widespread errors.
To start out, you may want to chop two items of binding which can be every twice the width of the quilt binding. Fold one piece of binding in half lengthwise and press it. Then, open up the binding and fold every uncooked edge in in direction of the middle crease. Press once more. Repeat with the second piece of binding. Now, you are prepared to affix the ends of the binding.
To hitch the ends of the binding, overlap the uncooked edges by about 1 inch. Fold the highest binding over the underside binding and sew collectively. Trim any extra binding. Flip the quilt over and fold the binding over the uncooked fringe of the quilt. Sew the binding in place. And that is it! You have now efficiently joined the ends of your quilt binding.
Collect the Ends and Trim Extra Seam
Measure and Mark the Binding Ends:
- Measure the size of the binding strips which can be hanging off the quilt.
- Mark the surplus seam allowance on every strip with a cloth marker, pen, or tailor’s chalk.
- The surplus seam allowance sometimes ranges from 1/4 inch to 1/2 inch.
Trim the Extra Seam Allowance:
- Fold the binding strip on the marked line and press it firmly to create a crease.
- Use sharp scissors to trim off the surplus seam allowance.
- Watch out to not reduce too near the stitches, as this might weaken the binding.
Collect the Trimmed Binding Ends:
- As soon as the surplus seam allowance has been trimmed, fold the binding strips again over the sting of the quilt and align them with the place to begin of the binding.
- The trimmed binding ends needs to be overlapped barely, sometimes by about 1/4 inch.
- Safe the gathered binding ends in place with a pin or clips.
Desk: Binding Strip Overlap
| Overlap Distance |
|—|—|
| 1/4 inch |
| 1/2 inch |
| 3/4 inch |
Trim the Extra Binding
As soon as the binding strips are sewn onto the quilt, it is time to trim the surplus material. This may give the quilt a clear and completed look. Observe these steps to trim the surplus binding:
- Fold the binding over the sting of the quilt. Press the fold to crease it.
- Trim the surplus binding on the diagonal. Reduce a 45-degree angle from the folded fringe of the binding to the uncooked fringe of the quilt. This may create a mitered nook when the binding is folded over.
- Unfold the binding and press it flat.
- Fold the binding over the uncooked fringe of the quilt once more. Press the fold to crease it.
- Trim the surplus binding on the alternative diagonal. Reduce one other 45-degree angle, beginning on the folded fringe of the binding and ending on the uncooked fringe of the quilt. This may create a second mitered nook.
| Step | Description |
|---|---|
| 1 | Fold the binding over the sting of the quilt and press the fold. |
| 2 | Trim the surplus binding on the diagonal, making a 45-degree angle. |
| 3 | Unfold the binding and press it flat. |
| 4 | Fold the binding over the uncooked fringe of the quilt once more and press the fold. |
| 5 | Trim the surplus binding on the alternative diagonal, making a second 45-degree angle. |
Fold Again the Binding Ends
Upon getting sewn the binding across the quilt, you will want to fold again the ends and sew them down securely. This may create a neat {and professional} end to your quilt. Listed below are the steps on find out how to fold again the binding ends:
1. Align the Binding Ends
Align the uncooked edges of the binding ends in order that they’re even. Guarantee that the appropriate sides of the material are dealing with one another.
2. Fold Again the Binding
Fold the binding again over the uncooked edges of the quilt by about 1/2 inch. Press the fold down with a heat iron.
3. Sew the Binding Ends
Topstitch the binding ends down utilizing a small sew. You need to use a hand-sewing needle or a stitching machine. In case you are utilizing a stitching machine, use a blind hem sew or a topstitch sew.
4. Trim the Extra Binding
Trim any extra binding that extends past the sting of the quilt. You need to use sharp scissors or a rotary cutter to trim the binding.
5. Safe the Knot
Tie a knot within the thread to safe the stitches. It’s also possible to use a dab of material glue to assist safe the knot.
6. Fold the Binding Ends Underneath
Fold the binding ends underneath the quilt by about 1/4 inch. This may assist to cover the uncooked edges of the binding. You need to use a heat iron to press the binding down.
Here’s a desk summarizing the steps on find out how to fold again the binding ends:
| Step | Description |
|---|---|
| 1 | Align the binding ends in order that they’re even. |
| 2 | Fold the binding again over the uncooked edges of the quilt by about 1/2 inch. |
| 3 | Topstitch the binding ends down utilizing a small sew. |
| 4 | Trim any extra binding that extends past the sting of the quilt. |
| 5 | Safe the knot. |
| 6 | Fold the binding ends underneath the quilt by about 1/4 inch. |
Hand Sew the Binding Ends Collectively
1. Fold the binding straps over the quilt’s edge, as should you have been hand-sewing the binding on.
2. On the first binding finish, deliver the needle up via the underside layer of the binding, on the high of the quilt nook.
3. Take the needle down via the alternative binding strap, on the backside of the quilt nook, about 1/4 inch from the sting.
4. Pull the thread tight, ensuring to not pull so tightly that you just pucker the material.
5. Repeat steps 2-4 till you attain the tip of the quilt.
6. On the final sew, come up via the binding fold after which down via the seam allowance of the binding.
7. Tie off the thread and trim any extra.
Here’s a abstract of the steps in a desk:
| Step | Description |
|---|---|
| 1 | Fold the binding straps over the quilt’s edge. |
| 2 | Deliver the needle up via the underside layer of the binding, on the high of the quilt nook. |
| 3 | Take the needle down via the alternative binding strap, on the backside of the quilt nook, about 1/4 inch from the sting. |
| 4 | Pull the thread tight, ensuring to not pull so tightly that you just pucker the material. |
| 5 | Repeat steps 2-4 till you attain the tip of the quilt. |
| 6 | On the final sew, come up via the binding fold after which down via the seam allowance of the binding. |
| 7 | Tie off the thread and trim any extra. |
Press the Binding Securely
As soon as the mitered corners have been sewn, it is important to press the binding securely to make sure a professional-looking end. This is an in depth information to urgent the binding securely:
1. Trim the Extra Binding
Trim the surplus binding on the mitered corners to about 1/4 inch past the purpose the place the stitches finish.
2. Fold the Binding Over the Edge
Fold the binding over the uncooked fringe of the quilt, guaranteeing it covers the uncooked edge utterly.
3. Press the Binding
Use a heat iron and press the binding in place, ranging from the middle of the quilt and dealing outwards. Press firmly to crease the binding alongside the sting.
4. Set the Iron Temperature
Set the iron temperature to the suitable setting for the material getting used. Keep away from utilizing too excessive a temperature, as this could scorch the material.
5. Use a Urgent Fabric
Place a urgent fabric over the binding to guard the material from direct warmth. This can even assist stop any shine or discoloration.
6. Press the Edges
Press the sides of the binding firmly to make sure they’re safe. Use a small iron or a mini iron for fantastic particulars, reminiscent of round buttons or different elaborations.
7. Crease the Binding
Crease the binding across the corners to create a pointy and clear end. Use a bone folder or a small ruler for precision.
8. Take away the Urgent Fabric
As soon as the binding is securely pressed, take away the urgent fabric and permit the quilt to chill barely.
9. Prime-stitch the Binding
For added sturdiness and an ornamental contact, top-stitch the binding in place. Use a contrasting thread shade or a thread that matches the binding material. The next desk gives pointers for top-stitching several types of binding:
| Binding Sort | Prime-Stitching Method |
|---|---|
| Machine-stitched binding | Prime-stitch near the sting of the binding, about 1/8 inch from the seam. |
| Hand-stitched binding | Use a blind sew to top-stitch the binding, catching just a few threads of the quilt high. |
| Bias-bound binding | Prime-stitch on the folded fringe of the bias tape, about 1/4 inch from the sting. |
How To Be a part of Quilt Binding Ends
To hitch the ends of your quilt binding, you will want to overlap the ends by about 2 inches. Fold one finish of the binding over the opposite in order that the uncooked edges are aligned. Sew the sides collectively, beginning about 1/2 inch from the tip of the binding. Sew all the best way to the tip of the binding, then backstitch to safe the seam.
Fold the joined ends of the binding over the sting of the quilt, in order that the uncooked edges are hidden. Sew the binding in place all the best way across the quilt, utilizing a blind sew or different invisible sew methodology.
Individuals Additionally Ask
How do you be a part of quilt binding ends with out a miter?
To hitch quilt binding ends with out a miter, merely overlap the ends by about 2 inches and sew them collectively. Make sure to backstitch at the start and finish of the seam to safe it.
How do you make a mitered nook for quilt binding?
To make a mitered nook for quilt binding, comply with these steps:
Step 1: Reduce the binding
Reduce two strips of binding which can be the identical size as the edges of the quilt. Fold one finish of every strip over by 1/2 inch and press.
Step 2: Align the binding strips
Align the 2 binding strips in order that the folded ends overlap by 1 inch. The uncooked edges of the binding needs to be aligned.
Step 3: Sew the binding strips collectively
Sew the binding strips collectively alongside the folded edges, beginning about 1/2 inch from the tip. Sew all the best way to the tip of the binding, then backstitch to safe the seam.
Step 4: Fold the binding over the quilt
Fold the joined binding strips over the sting of the quilt, in order that the uncooked edges are hidden. Sew the binding in place all the best way across the quilt, utilizing a blind sew or different invisible sew methodology.
