Badger rubbish disposals are a standard sight in lots of houses. They’re recognized for his or her sturdiness and effectivity, however even the perfect rubbish disposals can finally should be changed. In case you are contemplating eradicating a Badger rubbish disposal, there are some things it’s essential to know. First, you have to to disconnect the facility to the disposal. This may be completed by turning off the breaker that provides energy to the kitchen. As soon as the facility is disconnected, you possibly can start to take away the disposal.
To take away the disposal, you have to to first take away the mounting bolts that maintain it in place. These bolts are usually situated on the underside of the disposal. As soon as the bolts are eliminated, you possibly can rigorously carry the disposal out of the sink. Make sure you assist the disposal together with your different hand as you carry it out. As soon as the disposal is out of the sink, you possibly can disconnect the drain line and the facility twine.
Now that the disposal is disconnected, you possibly can get rid of it. Most rubbish disposals could be disposed of within the trash. Nonetheless, it’s possible you’ll must verify together with your native waste administration firm to see if there are any particular disposal necessities. As soon as the disposal is disposed of, you possibly can set up a brand new one. To put in a brand new disposal, merely observe the directions that got here with the brand new unit. Make sure you join the drain line and the facility twine earlier than turning on the facility to the brand new disposal.
Collect Important Instruments
Earlier than embarking on the duty of eradicating your Badger rubbish disposal, it’s essential to collect all the required instruments to make sure a clean and secure course of. The next is a complete record of important instruments you have to:
Wrench
An adjustable wrench is the first device for disconnecting the discharge tube and the mounting bolts that safe the disposal to the sink. Select a wrench with a snug grip and adequate leverage to loosen tight bolts.
Pliers
A pair of slip-joint pliers is crucial for eradicating {the electrical} wire connectors from the disposal’s motor. They supply a safe grip and forestall injury to the wires whereas disconnecting them.
Screwdriver
A screwdriver is required to take away the screws holding the dishwasher drain hose to the disposal’s dishwasher port. A Phillips head screwdriver is often used for this job.
Bucket
A bucket is important to gather any water or particles that will spill out in the course of the elimination course of. It additionally gives a handy place to retailer the eliminated components quickly.
Flashlight
A flashlight is useful for illuminating the disposal’s underside and for reaching into tight areas throughout disassembly. It enhances visibility and lets you work extra successfully.
Different Instruments
Further instruments which may be required for particular fashions or conditions embrace a putty knife, a flashlight, and a pair of gloves for hand safety. Making ready with the suitable instruments will streamline the elimination course of and forestall delays on account of lacking or insufficient instruments.
Disconnect the Energy Supply
To make sure your security in the course of the elimination course of, it is essential to disconnect the facility supply out of your Badger rubbish disposal.
Determine the Energy Supply
Find {the electrical} outlet or circuit breaker that provides energy to your rubbish disposal. The outlet is often beneath the sink, whereas the circuit breaker is normally in your house’s electrical panel.
Unplug the Outlet
In case your rubbish disposal is plugged into an outlet, merely unplug it. Use warning and keep away from touching the wires.
Flip Off the Circuit Breaker
In case your rubbish disposal is linked to a circuit breaker, find the corresponding breaker in your electrical panel. Flip the breaker to the “Off” place.
| Energy Supply Sort | Disconnection Methodology |
|---|---|
| Outlet | Unplug the facility twine. |
| Circuit Breaker | Flip the breaker to the “Off” place. |
Entry the Disposal
1. Flip off the facility to the disposal. This may be completed on the circuit breaker or fuse field.
2. Open the cupboard doorways beneath the sink.
3. Find the disposal. It will likely be a cylindrical-shaped unit mounted beneath the sink. There might be a big screw-on ring that holds the disposal in place.
4. Place a bucket or trash can beneath the disposal to catch any water or particles that will spill out.
5. Utilizing a screwdriver or wrench, loosen the screw-on ring that holds the disposal in place.
6. As soon as the ring is unfastened, you possibly can pull the disposal down from the sink. Watch out, as it could be heavy.
Disconnect the Wiring
1. As soon as the disposal is faraway from the sink, you have to to disconnect the wiring. There might be three wires which might be linked to the disposal: a black wire, a white wire, and a inexperienced or naked copper wire.
2. Utilizing a pair of pliers, disconnect the black and white wires from the terminals on the disposal.
3. Disconnect the inexperienced or naked copper wire from the bottom screw on the disposal.
4. As soon as the wires are disconnected, you possibly can take away the disposal from the sink.
Disassemble the Splash Guard
To disassemble the splash guard, observe these steps:
1. Find the 2 tabs on the facet of the splash guard.
2. Insert a screwdriver or different skinny object into the slots on the tabs.
3. Push down on the tabs to launch the splash guard.
4. Rigorously carry the splash guard up and off the disposal.
Detailed Directions for Step 4:
When lifting the splash guard up and off the disposal, watch out to not injury {the electrical} wires linked to the disposal. These wires are situated on the underside of the splash guard and could also be simply broken if they aren’t dealt with rigorously.
To keep away from damaging {the electrical} wires, observe these pointers:
- Assist the splash guard with one hand when you carry it up with the opposite.
- Don’t pull on {the electrical} wires.
- If {the electrical} wires are tangled, gently untangle them earlier than lifting the splash guard.
| Step | Description |
|---|---|
| 1 | Find the 2 tabs on the facet of the splash guard. |
| 2 | Insert a screwdriver or different skinny object into the slots on the tabs. |
| 3 | Push down on the tabs to launch the splash guard. |
| 4 | Rigorously carry the splash guard up and off the disposal. |
Disconnect the Mount Ring
The mount ring is the steel ring that secures the rubbish disposal to the sink. To take away the Badger rubbish disposal, you first must disconnect the mount ring. Here is find out how to do it:
- Flip off the facility to the rubbish disposal on the circuit breaker or fuse field.
- Unplug the rubbish disposal from the facility outlet.
- Place a bucket beneath the rubbish disposal to catch any water that will leak out.
- Use a wrench to loosen the bolts that safe the mount ring to the sink.
- Rigorously carry the rubbish disposal up and off the mount ring. Watch out to not injury the sink or the rubbish disposal.
| Bolt Dimension | Wrench Dimension |
|---|---|
| 1/2 inch | 12-inch adjustable wrench |
| 5/8 inch | 14-inch adjustable wrench |
| 3/4 inch | 16-inch adjustable wrench |
Take away the Disposal Physique
Detach {the electrical} wiring.
Disconnect the drain hose by loosening the clamp and sliding it off rigorously to keep away from splashing.
Disconnect the dishwasher drain hose by unscrewing the becoming connecting it to the disposal.
Take away the mounting bracket.
– To do that, you have to to find the three or 4 screws that maintain the bracket in place and take away them.
Rigorously decrease the disposal by loosening the mounting screws and pulling it down.
Clear the sink flange space totally earlier than putting in the brand new disposal.
Take away the Mounting Bracket
To take away the mounting bracket, you will want a Phillips head screwdriver. Observe these steps:
- Find the 2 screws that maintain the mounting bracket to the sink flange. These screws are usually situated on the underside of the sink flange, close to the sting of the sink.
- Use the Phillips head screwdriver to take away the 2 screws.
- As soon as the screws are eliminated, the mounting bracket needs to be unfastened. Now you can carry the mounting bracket away from the sink flange.
- If the mounting bracket is caught, it’s possible you’ll want to make use of a putty knife or a flathead screwdriver to pry it unfastened.
- As soon as the mounting bracket is eliminated, now you can entry the rubbish disposal unit.
- Repeat the identical steps on the opposite facet of the mounting bracket to take away it utterly.
- As soon as the mounting bracket is eliminated, now you can entry {the electrical} wires, drain pipe, and water provide traces which might be linked to the rubbish disposal unit.
Clear the Mounting Space
Earlier than eradicating the disposal, it is essential to scrub the mounting space totally. This may assist stop any particles or residue from stepping into the brand new disposal and inflicting issues.
Supplies Wanted:
| Merchandise | Amount |
|---|---|
| Comfortable cloths or rags | 2-3 |
| Clear water | 1 bucket |
| White vinegar (optionally available) | 1/2 cup |
| Gentle dish cleaning soap | Just a few drops |
Steps:
- Flip off the water provide: Find the shut-off valves beneath the sink and shut them.
- Unplug the disposal: Discover {the electrical} outlet the place the disposal is plugged in and disconnect it.
- Arrange your cleansing station: Fill a bucket with clear water and add a couple of drops of dish cleaning soap. If desired, it’s also possible to add 1/2 cup of white vinegar to assist take away odors.
- Wipe down the mounting space: Use a delicate material or rag dipped within the cleansing resolution to wipe down the mounting bolts, the mounting plate, and the encompassing space.
- Rinse the world: Dip a clear material or rag in clear water and rinse the mounting space totally.
- Dry the world: Use a dry material or rag to totally dry the mounting space.
- Examine the mounting bolts: Test the mounting bolts for any injury or rust. If any bolts are broken or rusted, they need to get replaced.
- Lubricate the mounting bolts (optionally available): To make it simpler to put in the brand new disposal, you possibly can apply a small quantity of petroleum jelly or silicone lubricant to the threads of the mounting bolts. Make sure you solely use a small quantity and wipe off any extra.
Reinstall the Disposal
Now that you’ve got the Badger rubbish disposal eliminated, it is time to reinstall it. In case you have {an electrical} outlet beneath your sink, plug within the new disposal. In case you wouldn’t have an outlet, you have to to run a brand new circuit to your sink. As soon as the disposal is plugged in, you possibly can connect it to the sink drain utilizing the mounting bracket.
As soon as the disposal is mounted, you possibly can join the drain line to the disposal. The drain line is the pipe that carries the wastewater from the sink to the disposal. To attach the drain line, merely slide the drain line onto the disposal’s drain connection. If vital, you should use a screwdriver to tighten the drain line onto the disposal.
As soon as the drain line is linked, you possibly can activate the water provide to the sink. Test for leaks across the disposal and the drain line. In case you discover any leaks, tighten the connections till the leaks cease.
Activate the disposal and let it run for a couple of minutes. This may assist to prime the disposal and be sure that it’s working correctly. If the disposal just isn’t working correctly, verify the circuit breaker to make sure that it’s not tripped. If the circuit breaker just isn’t tripped, it’s possible you’ll must name a plumber that can assist you troubleshoot the issue.
Restore Energy and Confirm Operation
1. Reset the Circuit Breaker or Change the Fuse
Find the circuit breaker or fuse field that controls the facility to the Badger rubbish disposal. If the breaker has tripped or the fuse has blown, reset or substitute it accordingly.
2. Test for Unfastened Connections
Tighten any unfastened wire connections on the circuit breaker or fuse field, in addition to any connections contained in the Badger rubbish disposal itself.
3. Isolate the Disposal from the Sink
Disconnect the Badger rubbish disposal from the sink by unscrewing the mounting bracket that holds it in place.
4. Disconnect the Electrical Wires
Rigorously disconnect {the electrical} wires from the Badger rubbish disposal’s motor. Notice the place of every wire for reconnecting later.
5. Take away the Badger Rubbish Disposal
Elevate the Badger rubbish disposal straight up and out of the sink gap, taking care to not injury the pipes or wiring.
6. Clear the Sink Gap
Completely clear the sink gap and take away any particles or obstructions that will have contributed to the disposal’s malfunction.
7. Set up the New Badger Rubbish Disposal
Insert the brand new Badger rubbish disposal into the sink gap and safe it with the mounting bracket.
8. Reconnect the Electrical Wires
Reconnect {the electrical} wires to the Badger rubbish disposal’s motor, guaranteeing that they’re correctly tightened.
9. Reinstall the Disposal into the Sink
Decrease the Badger rubbish disposal again into the sink gap and reconnect the mounting bracket.
10. Confirm Operation
Activate the Badger rubbish disposal and run water by it to make sure it’s working accurately. Test for any leaks, uncommon noises, or vibrations.
How To Take away A Badger Rubbish Disposal
Eradicating a Badger rubbish disposal is a comparatively easy job that may be accomplished in a couple of minutes with the precise instruments. Listed here are the steps on find out how to do it:
- Flip off the facility to the disposal. This may be completed on the circuit breaker or fuse field.
- Disconnect the water provide to the disposal. This may be completed by turning off the water valve beneath the sink.
- Loosen the mounting bolts. There are usually three or 4 mounting bolts that maintain the disposal in place. Use a wrench to loosen these bolts.
- Disconnect {the electrical} wires. There are usually two electrical wires that join the disposal to the facility supply. Use a screwdriver to disconnect these wires.
- Take away the disposal. As soon as the mounting bolts and electrical wires are disconnected, you possibly can take away the disposal from the sink. Watch out to not drop it, as it’s heavy.
Folks Additionally Ask About How To Take away A Badger Rubbish Disposal
How do I take away theBadger rubbish disposal housing?
To take away the Badger rubbish disposal housing, you have to to disconnect the facility to the disposal, disconnect the water provide, and take away the mounting bolts. As soon as the mounting bolts are eliminated, you possibly can pull the housing straight as much as take away it.
How do I take away the Badger rubbish disposal motor?
To take away the Badger rubbish disposal motor, you have to to take away the housing first. As soon as the housing is eliminated, you will note the motor. There are usually three or 4 bolts that maintain the motor in place. Use a wrench to loosen these bolts and take away the motor.
How do I take away the Badger rubbish disposal blades?
To take away the Badger rubbish disposal blades, you have to to take away the motor first. As soon as the motor is eliminated, you will note the blades. There’s a single bolt that holds the blades in place. Use a wrench to loosen this bolt and take away the blades.
