Changing a two-handle bathtub faucet just isn’t as troublesome as it could appear. With a number of easy instruments and a little bit little bit of persistence, you’ll be able to have your new faucet put in very quickly.
Step one is to show off the water provide to the tub. That is normally accomplished by turning off the valves positioned underneath the sink. As soon as the water is turned off, you’ll be able to take away the outdated faucet by unscrewing the nuts that maintain it in place. Watch out to not harm the plumbing if you end up doing this.
As soon as the outdated faucet is eliminated, you’ll be able to set up the brand new one. Begin by inserting the brand new faucet within the gap within the bathtub. Then, screw on the nuts that maintain it in place. You should definitely tighten the nuts securely, however don’t overtighten them. Lastly, activate the water provide and verify for leaks. If there are any leaks, tighten the nuts till the leaks cease.
Collect Vital Instruments and Supplies
Changing a two-handle bathtub faucet requires a number of important instruments and supplies to make sure a clean and profitable set up. Here is a complete record of what you may want:
Instruments
- Adjustable wrench or spanner
- Phillips head screwdriver
- Flat head screwdriver
- Plumbers putty or Teflon tape
- Bucket or bowl
- Rags or towels
Supplies
| Element | Amount |
|---|---|
| New two-handle bathtub faucet | 1 |
| Faucet handles | 2 |
| Faucet aerators (elective) | 2 |
| Pipe dope or thread sealant | As wanted |
Moreover, chances are you’ll need to contemplate bringing a flashlight for higher visibility underneath the sink and a pair of labor gloves for defense.
Flip Off Water
Earlier than you start engaged on the tap, it is vital to show off the water provide. This can forestall water from spraying out of the tap whenever you take away the handles and cartridge. To show off the water provide, find the shut-off valves underneath the sink. The valves will usually be positioned on the base of the tap, the place the water strains hook up with the tap. Flip the valves clockwise to show off the water provide.
If there are not any shut-off valves underneath the sink, you’ll need to show off the water provide to all the home. To do that, find the primary water shut-off valve, which is normally positioned close to the entrance of the home, within the basement, or in a utility closet. Flip the valve clockwise to show off the water provide.
Ideas for Turning Off the Water
Listed below are a number of suggestions for turning off the water provide:
- Just remember to have a wrench or pliers available to show the shut-off valves.
- If the shut-off valves are troublesome to show, you’ll be able to attempt utilizing a pair of pliers to get a greater grip.
- In case you are unable to show off the water provide, you must name a plumber for help.
| Instrument | Function |
| Wrench or pliers | To show the shut-off valves |
Take away Aerators and Handles
Eradicating Aerators
Begin by unscrewing the aerator from the tap utilizing a wrench. If the aerator is caught, you should use a pair of pliers to softly loosen it.
As soon as the aerator is eliminated, it is possible for you to to see the cartridge. The cartridge is held in place by a screw, which you’ll need to take away utilizing a screwdriver.
As soon as the screw is eliminated, it is possible for you to to elevate the cartridge out of the tap. Watch out to not lose the washer that’s positioned behind the cartridge.
Eradicating Handles
To take away the handles, you’ll need to find the set screws which are holding them in place. The set screws are normally positioned on the underside of the handles.
After getting positioned the set screws, you’ll need to loosen them utilizing a screwdriver. Watch out to not over-tighten the set screws, as this could harm the handles.
As soon as the set screws are loosened, it is possible for you to to tug the handles off the tap.
| Instrument | Description |
|---|---|
| Wrench | Used to unscrew the aerator. |
| Screwdriver | Used to take away the cartridge screw and set screws. |
| Pliers | Used to loosen a caught aerator. |
| Washer | Situated behind the cartridge, it should not be misplaced. |
| Set screws | Maintain the handles in place. |
Disconnect Provide Traces
As soon as the handles and trim are eliminated, you’ll need to disconnect the provision strains. These are the versatile hoses that join the tap to the water provide pipes. Use an adjustable wrench to loosen the nuts that join the hoses to the tap.
Watch out to not overtighten the nuts, as you’ll be able to harm the hoses. As soon as the nuts are free, you’ll be able to rigorously pull the hoses off the tap.
If the hoses are outdated or broken, chances are you’ll want to interchange them. To do that, minimize the outdated hoses off the tap and the provision pipes. Then, connect the brand new hoses to the tap and the provision pipes utilizing the nuts that got here with the brand new hoses.
As soon as the provision strains are disconnected, you’ll be able to take away the outdated faucet from the sink or tub.
| Ideas |
|---|
| In case you are having hassle disconnecting the provision strains, you should use a pair of pliers that will help you loosen the nuts. |
| Watch out to not harm the provision strains if you end up disconnecting them. |
| In case you are changing the provision strains, ensure that they’re the proper size and that they’re rated for the water strain in your house. |
Take away Faucet Base
After eradicating the handles and cartridge, now you can take away the tap base. Place a bucket or towel underneath the tap to catch any water which will leak out.
Utilizing an adjustable wrench, loosen the nuts which are holding the tap base in place. Watch out to not overtighten the nuts, as this could harm the tap.
As soon as the nuts are free, you’ll be able to gently pull the tap base off of the bathtub deck.
If the tap base is caught, chances are you’ll want to make use of a rubber mallet to softly faucet it free. Watch out to not hit the tap too arduous, as this could harm it.
As soon as the tap base is eliminated, now you can entry the plumbing connections.
Ideas for Eradicating the Faucet Base
| Ideas | Particulars |
|---|---|
| Use a bucket or towel to catch any water which will leak out | This can assist to forestall water from damaging your flooring or carpet. |
| Watch out to not overtighten the nuts | Overtightening the nuts can harm the tap. |
| If the tap base is caught, use a rubber mallet to softly faucet it free | Watch out to not hit the tap too arduous, as this could harm it. |
Clear Mounting Floor
Earlier than you start putting in the brand new faucet, it is vital to completely clear the mounting floor. This can assist to make sure that the brand new faucet is put in securely and that there are not any leaks. Listed below are the steps to wash the mounting floor:
-
Take away any outdated caulk or sealant from across the outdated faucet. You should use a utility knife or a razor blade to rigorously scrape away the caulk.
-
Clear the floor with a degreaser. This can assist to take away any dust, grime, or oil that would forestall the brand new faucet from bonding correctly.
-
Rinse the floor with clear water and permit it to dry utterly.
| Tip | Description |
|---|---|
| Use a scrub brush to wash the floor completely. | This can assist to take away any cussed dust or grime. |
| Enable the floor to dry utterly earlier than putting in the brand new faucet. | This can assist to make sure that the brand new faucet is put in securely. |
Apply Plumber’s Putty and Set up Base
Step 7: Apply Plumber’s Putty and Set up Base
7.1: Take away the outdated plumber’s putty from the bottom of the brand new faucet utilizing a putty knife or scraper. Clear the realm completely with rubbing alcohol and permit it to dry.
7.2: Roll out a rope of plumber’s putty about 1/4 inch thick and 6 inches lengthy. Place the putty across the base of the tap, leaving a small gap within the heart for the water provide strains.
7.3: Flip the tap the wrong way up and place it over the mounting holes within the bathtub. Be sure that the putty is evenly distributed across the base and filling any gaps.
7.4: Place the mounting bolts by means of the holes within the faucet and into the tub. Tighten the nuts by hand till comfortable.
7.5: Flip the tap right-side up and manually tighten the mounting nuts additional. Keep away from overtightening, as this could harm the tap or bathtub.
7.6: Use a degree to make sure the tap is degree. Regulate the mounting nuts as needed.
Set up Handles
1. Place the handles on the stems.
2. Apply a small quantity of plumbers grease to the threads of the deal with screws.
3. Insert the deal with screws into the handles and tighten them till they’re comfortable.
4. Use a wrench to tighten the packing nuts on every deal with.
5. Activate the water and verify for leaks. If there’s a leak, tighten the packing nuts till the leak stops.
6. Set up the aerators on every deal with.
7. Activate the water and verify for leaks. If there’s a leak, tighten the aerators till the leak stops.
8. Examine the operation of the tap. The handles ought to flip easily and the water ought to circulate evenly from the aerators. If the tap doesn’t function correctly, verify the next:
| Attainable Drawback | Resolution |
|---|---|
| The handles are stiff | Loosen the packing nuts on the handles |
| The water doesn’t circulate evenly from the aerators | Clear the aerators |
| The tap is leaking | Tighten the packing nuts on the handles or aerators |
Join Provide Traces
9. **Join Provide Traces to Faucet:**
a. Wrap plumber’s tape clockwise across the threaded finish of the cold and hot provide strains. Tighten them by hand onto the corresponding faucet inlets marked “H” and “C.”
b. **Use a Basin Wrench to Safe:**
| Tip | Profit |
|---|---|
| Insert a basin wrench into the outlet within the faucet physique. | Permits entry to the nuts beneath the tap. |
| Tighten the nuts till they’re comfortable, however keep away from overtightening. | Prevents leaks and ensures a safe connection. |
c. **Examine Connections:**
Activate the water provide and verify for leaks on the faucet inlets and provide line connections. If any leaks happen, tighten the connections additional as wanted.
Flip On Water and Examine for Leaks
As soon as the outdated faucet is eliminated, it is essential to activate the water provide to check for any potential leaks earlier than putting in the brand new one. Comply with these steps to make sure a watertight seal:
- Open each the cold and hot water valves positioned beneath the sink.
- Run each handles to permit water to circulate by means of the pipes.
- Examine the bottom of the tap, the provision strains, and every other connections for any indicators of water leakage.
- Should you encounter any leaks, tighten the connections additional utilizing a wrench or pliers.
- As soon as the leaks have been addressed, flip off each water valves once more.
- Proceed with the set up of the brand new faucet, taking additional care to safe all connections.
- As soon as the brand new faucet is totally put in, activate the water valves once more and verify for any remaining leaks.
- If all connections are safe and there are not any leaks, proceed to the subsequent step of testing the performance of the tap.
- Should you encounter any persistent leaks that can not be resolved, seek the advice of a licensed plumber for skilled help.
| Troubleshooting Leaks | |
|---|---|
| Leak at faucet base | Tighten the locknut beneath the tap. |
| Leak at provide line connections | Use a wrench to tighten the nuts connecting the provision strains to the tap. |
| Leak at pop-up drain | Examine the drain stopper meeting and substitute any worn-out parts. |
How To Exchange A Two Deal with Bathtub Faucet
Changing a two-handle bathtub faucet is a comparatively easy activity that may be accomplished in a number of hours. With the precise instruments and supplies, it can save you your self the price of hiring a plumber.
Instruments and Supplies
• Adjustable wrench
• Basin wrench
• Plumber’s putty
• Teflon tape
• New bathtub faucet
• Utility knife
Directions
- Flip off the water provide to the tub. There needs to be two shut-off valves positioned underneath the sink. Flip the handles clockwise to shut them.
- Open the tub faucet to launch any remaining water strain.
- Use the adjustable wrench to loosen the nuts that maintain the handles in place. Take away the handles.
- Use the basin wrench to loosen the nuts that maintain the tap physique in place. Take away the tap physique.
- Apply a bead of plumber’s putty to the bottom of the brand new faucet physique. Wrap the threads of the tap physique with Teflon tape.
- Set up the brand new faucet physique and tighten the nuts with the basin wrench.
- Set up the handles and tighten the nuts with the adjustable wrench.
- Activate the water provide to the tub and verify for leaks. If there are any leaks, tighten the nuts additional.
Folks Additionally Ask About How To Exchange A Two Deal with Bathtub Faucet
How a lot does it price to interchange a tub faucet?
The price to interchange a tub faucet can differ relying on the kind of faucet you select and the complexity of the set up. Nonetheless, you’ll be able to count on to pay between $100 and $500 for the tap and set up.
Can I substitute a tub faucet myself?
Sure, you’ll be able to substitute a tub faucet your self with the precise instruments and supplies. Nonetheless, in case you are not comfy working with plumbing, it’s best to rent a plumber.
What’s the greatest kind of bath faucet to purchase?
The most effective kind of bath faucet for you’ll rely in your wants and preferences. Some fashionable kinds of bathtub taps embrace:
- Two-handle taps
- Single-handle taps
- Thermostatic taps
- Sensor taps
