Are you bored with your PS5 controller malfunctioning? Do you wish to repair it your self however do not know the place to start out? Taking aside a PS5 controller could be a daunting process, nevertheless it’s not as troublesome as you may assume. With the precise instruments and somewhat little bit of endurance, you’ll be able to have your controller up and working once more very quickly.
Earlier than you begin, it is vital to assemble the mandatory instruments. You will have a Phillips #00 screwdriver, a T8 Torx screwdriver, and a plastic spudger. You will discover these instruments at most {hardware} shops or on-line. Upon getting your instruments, you’ll be able to start the disassembly course of.
Step one is to take away the 4 screws on the again of the controller. As soon as the screws are eliminated, you’ll be able to fastidiously pry the again panel off utilizing the plastic spudger. Watch out to not injury the ribbon cable that connects the again panel to the controller.
1. Eradicating the Outer Shell
Supplies:
- Phillips #000 screwdriver
- Nylon spudger
- Small plastic tray
Steps:
- Take away the 4 seen screws: Find the 4 Phillips #000 screws on the again of the controller and take away them. Be aware: The screws are small, so watch out to not lose them.
- Pop open the battery cowl: Insert the nylon spudger into the seam between the battery cowl and the controller, close to the underside. Rigorously pry open the quilt and set it apart.
- Unclip the shell halves: Utilizing the spudger, gently pry aside the controller’s shell halves. Begin on the prime, the place the buttons are positioned, and work your method right down to the underside. Be cautious to not injury the shell or its clips.
- Find the 2 hidden screws: As soon as the shell halves are separated, you will discover two further Phillips #000 screws hidden beneath the battery cowl. Take away these screws.
- Disconnect the battery: Gently carry the battery out of its compartment and disconnect the battery connector from the mainboard. Place the battery within the plastic tray for safekeeping.
- Separate the shell halves: With the battery disconnected, now you can fully separate the 2 controller shell halves. The inside elements, together with the mainboard, buttons, and joysticks, will likely be uncovered.
Step 2: Eradicating the Faceplate
Now comes the difficult half, because the faceplate is held in place by clips across the edges, and prying it open requires a little bit of finesse to keep away from damaging the controller’s shell. Start by finding the small screw gap on the again of the controller, just under the L2 button. Utilizing a Phillips #00 screwdriver, fastidiously take away the screw and set it apart.
Subsequent, flip the controller over and place it on a gentle floor to keep away from scratching it. Utilizing a plastic spudger or a skinny guitar decide, insert the device into the slender hole between the faceplate and the physique of the controller, close to the highest edge or backside edge. Gently pry the device upward, making use of regular stress till you hear a click on, indicating the clip has been launched. Repeat this course of across the edges, working your method clockwise or counterclockwise, till all of the clips are disengaged.
As soon as all of the clips are launched, the faceplate ought to come free. Rigorously carry it off, taking care to not injury the ribbon cable that connects the faceplate to the controller’s mainboard. Place the faceplate apart in a protected place.
| Instruments Wanted: |
|---|
| Phillips #00 screwdriver |
| Plastic spudger or guitar decide |
Important Instruments and Supplies for PS5 Controller Disassembly
Instruments for Eradicating Exterior Screws
* Small Phillips-head screwdriver: A #0 or #00 Phillips-head screwdriver is appropriate for eradicating the exterior screws that safe the controller’s outer shell.
* Magnetized screwdriver: A magnetized screwdriver helps stop screws from falling out after they’re loosened.
* Tweezers: Tweezers will be useful for retrieving screws which have fallen into tight areas.
Instruments for Eradicating Inner Parts
* Plastic pry device: A skinny, versatile plastic pry device is important for separating the controller’s elements with out damaging them.
* Spudger: A spudger is a small, wedge-shaped device that can be utilized to softly pry aside clips and connectors.
* Screwdriver set: A set of small, precision screwdrivers could also be wanted for eradicating inner screws that aren’t accessible with the exterior screwdriver.
Cleansing and Lubricating Supplies
* Isopropyl alcohol (90% or greater): Isopropyl alcohol is a superb solvent for cleansing dust and grease from the controller’s elements.
* Compressed air: Compressed air can be utilized to take away free mud and particles from the controller.
* Cotton swabs and wipes: Cotton swabs and wipes are helpful for making use of cleansing options and lubricating contact factors.
* Conductive grease: Conductive grease is a specialised lubricant that may be utilized to the controller’s contact factors to enhance electrical conductivity.
| Materials | Goal |
|---|---|
| Phillips-head screwdriver | Take away exterior screws |
| Magnetized screwdriver | Maintain screws in place |
| Tweezers | Retrieve free screws |
| Plastic pry device | Separate elements |
| Spudger | Pry aside clips and connectors |
| Isopropyl alcohol | Clear dust and grease |
| Compressed air | Take away free mud |
| Cotton swabs and wipes | Apply cleansing options and lubricants |
| Conductive grease | Enhance electrical conductivity |
Security Precautions to Take into account When Taking Aside a PS5 Controller
Taking aside a PS5 controller can seem to be a frightening process, however by following the right security precautions and procedures, you’ll be able to full it safely and successfully. Earlier than you start, listed here are a number of essential security issues to remember:
1. Disconnect the Controller from Energy Sources
Be certain that the controller is totally disconnected from any energy sources, such because the console or a USB port. This can assist stop electrical shocks and potential injury to the controller or its elements.
2. Use Correct Instruments
Have the precise instruments for the job. You will have a small Phillips head screwdriver and probably a spudger or plastic pry device to open the controller housing. Utilizing inappropriate instruments may cause injury to the controller or make the disassembly course of tougher.
3. Put on Gloves
Take into account sporting gloves in the course of the course of to keep away from transferring oils or dust out of your arms to the controller’s inner elements. This can assist preserve the elements clear and forestall any potential contamination.
4. Deal with the Battery Rigorously
The PS5 controller homes a lithium-ion battery. It’s essential to deal with the battery with the utmost care. Keep away from puncturing, crushing, or bending the battery. If the battery reveals any indicators of injury or leaking, don’t proceed with the disassembly course of. Deal with the battery with warning and get rid of it correctly in keeping with native rules.
| Battery Dealing with Suggestions |
|---|
|
Figuring out the Key Parts of a PS5 Controller
The PS5 controller, formally referred to as the DualSense, is a posh piece of {hardware} that gives a variety of options and performance. Understanding the important thing elements of the controller is important for understanding the way it works and keep it correctly.
Analog Sticks
The 2 analog sticks on the PS5 controller present precision management for motion and aiming in video games. Every stick has a rubberized grip for consolation and a capacitive sensor that detects the place of your thumb. The sticks are additionally pressure-sensitive, permitting for fine-tuned management.
Buttons
The PS5 controller has a complete of 14 buttons, together with the 4 face buttons (triangle, circle, sq., and cross), the 2 triggers, the 2 shoulder buttons, the D-pad, the Choices button, the Share button, the Create button, and the PlayStation button. Every button has a selected perform in video games, and a few buttons will be personalized to fit your preferences.
Movement Sensors
The PS5 controller encompasses a six-axis movement sensor that detects the motion and orientation of the controller in three-dimensional house. This movement sensor is used to manage video games in a wide range of methods, resembling tilting the controller to goal or steering autos by turning the controller.
Constructed-in Microphone
The PS5 controller has a built-in microphone that lets you talk with different gamers in on-line video games. The microphone is positioned on the underside of the controller, close to the D-pad. You may mute the microphone by urgent the Mute button on the again of the controller.
Headset Jack
The PS5 controller has a 3.5mm headset jack that lets you join a wired headset to the controller. The headset jack is positioned on the underside of the controller, subsequent to the built-in microphone. You should utilize a headset to hearken to recreation audio, chat with different gamers, and document your individual voice.
| Element | Perform |
|---|---|
| Analog Sticks | Precision management for motion and aiming |
| Buttons | Particular capabilities in video games |
| Movement Sensors | Detect motion and orientation of the controller |
| Constructed-in Microphone | Talk with different gamers in on-line video games |
| Headset Jack | Join a wired headset to the controller |
Eradicating the Faceplate and Buttons
To take away the faceplate, you will want a small screwdriver or pry device. Insert the device into the small notch on the underside fringe of the faceplate and gently pry it off. Watch out to not injury the faceplate or the controller itself.
As soon as the faceplate is eliminated, you will have entry to the buttons. To take away a button, merely pull it straight up. Watch out to not lose the small spring that sits beneath every button.
Here’s a desk summarizing the steps for eradicating the faceplate and buttons:
| Step | Directions |
|---|---|
| 1 | Insert the screwdriver or pry device into the notch on the underside fringe of the faceplate. |
| 2 | Gently pry the faceplate off. |
| 3 | Pull the buttons straight as much as take away them. |
| 4 | Watch out to not lose the springs beneath the buttons. |
Disassembling the Analog Sticks and Triggers
Unfastening the Panel
Find the 4 plastic tabs on the again of the controller and gently pry them free. They are often discovered close to the analog sticks and shoulder buttons.
Eradicating the PCB and Battery
Disconnect the battery and PCB by eradicating the small 2-pin connector positioned close to the underside of the controller. Rigorously carry the PCB out of the controller housing.
Unscrewing the Analog Stick Modules
Utilizing a T8 Torx screwdriver, take away the 2 screws securing every analog stick module. Carry the modules out of the controller carcasa.
| Screw Location | Variety of Screws |
|---|---|
| Analog Stick Module (Left) | 2 |
| Analog Stick Module (Proper) | 2 |
Detaching the Triggers
Unclip the triggers from the controller housing by gently pulling them upwards. Chances are you’ll want to use some drive, however watch out to not injury them.
Eradicating the Touchpad
Utilizing a T8 Torx screwdriver, take away the 4 screws securing the touchpad. Carry the touchpad out of the controller housing.
Unplugging the Ribbon Cables
Disconnect the ribbon cables connecting the touchpad to the PCB. This can assist you to absolutely take away the touchpad and triggers.
Detaching the Battery
Find the battery, an oblong part located inside the chassis. Use a Phillips #00 screwdriver to take away the 2 screws securing the battery. Rigorously carry the battery out of its compartment.
Haptic Suggestions Motors
Establish the 2 haptic suggestions motors, positioned on the rear and entrance of the chassis. Use a Phillips #00 screwdriver to take away the 4 screws securing every motor. Gently pry the motors free from their housings.
| Motor | Place | Screws |
|---|---|---|
| Rear | Again of the chassis | 4 |
| Entrance | Entrance of the chassis | 4 |
Eradicating the Motherboard and Different Inner Elements
As soon as the battery is disconnected, you’ll be able to start eradicating the motherboard and different inner elements. Listed below are the steps to comply with:
1. Take away the Warmth Sink
Find the warmth sink on the motherboard, which is usually secured by 4 screws. Take away the screws and carry off the warmth sink to show the motherboard.
2. Disconnect the Ribbon Cables
There are three ribbon cables that join the motherboard to different inner elements: the digicam cable, the touchpad cable, and the button cable. Use tweezers to fastidiously disconnect these cables from the motherboard.
3. Take away the Motherboard Screws
Find the six screws that safe the motherboard to the controller’s body. Take away the screws and punctiliously carry out the motherboard.
4. Take away the Inner Parts
The next inner elements are linked to the motherboard:
| Element | Connection | Left and proper triggers | Ribbon cable | Digicam | Ribbon cable | Audio system | Ribbon cable | Touchpad | Ribbon cable | Headphone jack | Ribbon cable |
|---|
Rigorously disconnect every part from the motherboard and take away it from the controller.
Step-by-Step PS5 Controller Disassembly Information
Earlier than disassembling your PS5 controller, guarantee it is powered off and disconnected from any units. Comply with these detailed steps fastidiously to forestall injury.
1. Take away Entrance Shell Screws
Use a Phillips #00 screwdriver to unscrew the 4 screws positioned beneath the entrance shell.
2. Separate the Entrance Shell
Rigorously pry open the entrance shell utilizing a plastic opening device or your trimmed nails.
3. Disconnect Battery
Find the battery connector and gently pull it out of its socket utilizing your fingernails or a non-metallic device.
4. Unscrew PCB Screw
Use a Phillips #00 screwdriver to take away the only screw securing the PCB board.
5. Carry PCB
Rigorously carry the PCB board straight up, being conscious of any ribbon cables.
6. Take away Set off Buttons
Gently pull the set off buttons away from the controller’s body.
7. Unscrew Rumble Motor Screws
Use a Phillips #00 screwdriver to unscrew the 4 screws holding the rumble motors in place.
8. Disconnect Rumble Motors
Rigorously disconnect the rumble motors from the PCB board by unplugging their connectors.
9. Unscrew Analog Stick Modules
Use a Tri-Wing Y00 screwdriver to unscrew the 4 screws securing every analog stick module.
10. Take away Analog Stick Modules
Tilt the analog stick modules barely and gently pull them out of the controller’s body. Watch out to not injury the fragile potentiometers or ribbon cables.
11. Unscrew Again Buttons Board
Use a Phillips #00 screwdriver to unscrew the 2 screws securing the again buttons board.
12. Disconnect Again Buttons Board
Rigorously unplug the again buttons board from its connector on the PCB board.
13. Unscrew Mild Bar Cowl Screw
Use a Phillips #00 screwdriver to take away the screw securing the sunshine bar cowl.
14. Carry Mild Bar Cowl
Rigorously pry open the sunshine bar cowl utilizing a plastic opening device or your trimmed nails.
15. Unscrew Mild Bar
Use a Phillips #00 screwdriver to unscrew the 4 screws securing the sunshine bar.
16. Disconnect Mild Bar
Rigorously unplug the sunshine bar connector from the PCB board.
17. Take away Again Shell
Rigorously separate the again shell from the remainder of the controller.
18. Unscrew Touchpad
Use a Phillips #00 screwdriver to unscrew the 4 screws securing the touchpad.
19. Carry Touchpad
Rigorously carry the touchpad away from the controller’s body.
20. Unscrew D-Pad
Use a Phillips #00 screwdriver to unscrew the 2 screws securing the D-pad.
21. Carry D-Pad
Rigorously carry the D-pad away from the controller’s body.
22. Unscrew Face Buttons
Use a Phillips #00 screwdriver to unscrew the 2 screws securing every face button.
23. Carry Face Buttons
Rigorously carry the face buttons away from the controller’s body.
24. Take away Deal with Grips
Rigorously pry open the deal with grips utilizing a plastic opening device or your trimmed nails.
25. Take away Begin and Share Buttons
Rigorously pull the beginning and share buttons out of the controller’s body.
26. Take away Choice and Create Buttons
Rigorously pull the choice and create buttons out of the controller’s body.
Knowledgeable Suggestions for Reassembling and Calibrating Your PS5 Controller
Recalibrate the Analog Sticks Utilizing the Console
After reassembling your controller, join it to your PS5 console. Navigate to “Settings” > “Equipment” > “Controllers” > “Calibrate Analog Sticks.” Comply with the on-screen directions to regulate the analog sticks’ sensitivity and accuracy.
Tighten All Screws Securely
Guarantee all screws are correctly tightened to forestall free elements or malfunctions. Keep away from overtightening, as it might probably strip the screws or injury the controller.
Take a look at Button Features
As soon as reassembled, take a look at all buttons, triggers, and analog sticks to make sure they’re functioning accurately. If any buttons are sticking or unresponsive, recheck the connections or contact PlayStation help.
Tips on how to Take a PS5 Controller Aside
The PlayStation 5 controller is a well-made piece of {hardware}, however there could come a time when it’s essential take it aside to restore or exchange a part. Taking aside the PS5 controller shouldn’t be troublesome, however there are some things you want to remember to keep away from damaging the controller.
- Take away the again panel. The again panel of the PS5 controller is held in place by 4 screws. Take away these screws utilizing a Phillips #00 screwdriver.
- Disconnect the battery. The battery is positioned within the backside of the controller. Disconnect the battery by pulling the connector straight out of the socket.
- Take away the screws holding the motherboard in place. There are 4 screws holding the motherboard in place. Take away these screws utilizing a Phillips #00 screwdriver.
- Rigorously carry the motherboard out of the controller. The motherboard is linked to the controller by a ribbon cable. Watch out to not injury the ribbon cable when lifting the motherboard out of the controller.
- Substitute the part it’s essential restore or exchange. Upon getting the motherboard out of the controller, you’ll be able to exchange the part it’s essential restore or exchange.
- Reassemble the controller. To reassemble the controller, merely comply with the steps in reverse order.
Folks Additionally Ask
How do I open a PS5 controller with out a screwdriver?
There is no such thing as a option to open a PS5 controller with out a screwdriver. The screws that maintain the again panel in place are very small and require a particular screwdriver to take away them.
How do I repair a PS5 controller that’s not charging?
In case your PS5 controller shouldn’t be charging, there are some things you’ll be able to strive:
- Attempt utilizing a special USB cable.
- Attempt plugging the controller into a special USB port.
- Attempt resetting the controller by holding down the PS button and the Share button for five seconds.
- If none of those steps work, it’s possible you’ll want to interchange the battery.
How do I clear a PS5 controller?
To wash a PS5 controller, you should utilize a gentle, damp material. Make sure to keep away from utilizing any harsh chemical compounds or cleaners, as these might injury the controller.
